8086 - Addressing Modes oo7

ΠΟΛΥΤΕΧΝΙΚΗ ΣΧΟΛΗ Τμήμα Ηλεκτρολογών Μηχανικών και Τεχνολογίας Υπολογιστών

Μικρουπολογιστές & Μικροσυστήματα ΙΙ Καθηγητής Σταύρος Α. Κουμπιάς Πανεπιστημίου Πατρών

•

•

The 80x86 Addressing Modes

The 80x86 processors let you access memory in many different ways. The 80x86 memory addressing modes provide flexible access to memory, allowing you to easily access variables, arrays, records, pointers, and other complex data types. Mastery of the 80x86 addressing modes is the first step towards mastering 80x86 assembly language. When Intel designed the original 8086 processor, they provided it with a flexible, though limited, set of memory addressing modes. Intel added several new addressing modes when it introduced the 80386 microprocessor. Note that the 80386 retained all the modes of the previous processors; the new modes are just an added bonus. If you need to write code that works on 80286 and earlier processors, you will not be able to take advantage of these new modes. However, if you intend to run your code on 80386sx or higher processors, you can use these new modes. Since many programmers still need to write programs that run on 80286 and earlier machines, it's important to separate the discussion of these two sets of addressing modes to avoid confusing them.

2

3

4

8086 Addressing Modes (I)

• Most 8086 instructions can operate on the 8086's general purpose set. By specifying the name of the as an operand to the instruction, you may access the contents of that . Consider the 8086 mov (move) instruction: mov destination, source

This instruction copies the data from the source operand to the destination operand. The eight and 16 bit s are certainly valid operands for this instruction. The only restriction is that both operands must be the same size. • Now let's look at some actual 8086 mov instructions: mov mov mov mov mov mov

ax, bx ;Copies the value from BX into AX dl, al ;Copies the value from AL into DL si, dx ;Copies the value from DX into SI sp, bp ;Copies the value from BP into SP dh, cl ;Copies the value from CL into DH ax, ax ;Yes, this is legal!

•

5

8086 Addressing Modes (II) •

•

•

•

The s are the best place to keep often used variables. Instructions using the s are shorter and faster than those that access memory. The abbreviated operands reg and r/m (/memory) used wherever you may use one of the 8086's general purpose s. In addition to the general purpose s, many 8086 instructions (including the mov instruction) allow you to specify one of the segment s as an operand. There are two restrictions on the use of the segment s with the mov instruction. First of all, you may not specify cs as the destination operand, second, only one of the operands can be a segment . You cannot move data from one segment to another with a single mov instruction. To copy the value of cs to ds, you'd have to use some sequence like: mov ax, cs, mov ds, ax You should never use the segment s as data s to hold arbitrary values. They should only contain segment addresses. The abbreviated operand sreg used wherever segment operands are allowed (or required).

6

8086 Memory Addressing Modes (Ι) memory. This may • The 8086 provides 17 different ways to access seem like quite a bit at first, but fortunately most of the address modes are simple variants of one another so they're very easy to learn. • The key to good assembly language programming is the proper use of memory addressing modes. • The addressing modes provided by the 8086 family include: displacement-only, base, displacement plus base, base plus indexed, and displacement plus base plus indexed. • Variations on these five forms provide the 17 different addressing modes on the 8086.

7

8086 Memory Addressing Modes (ΙΙ) The Displacement Only Addressing Mode The most common addressing mode, and the one that's easiest to understand, is the displacement-only (or direct) addressing mode. The displacement-only addressing mode consists of a 16 bit constant that specifies the address of the target location. The instruction mov al,ds:[8088h] loads the al with a copy of the byte at memory location 8088h. Likewise, the instruction mov ds:[1234h],dl stores the value in the dl to memory location 1234h:

8

8086 Memory Addressing Modes (IΙΙ) The Displacement Only Addressing Mode •Intel named this the displacement-only addressing mode because a 16 bit constant (displacement) follows the mov opcode in memory. In that respect it is quite similar to the direct addressing mode on the x86 processors. •There are some minor differences, however. First of all, a displacement is exactly that- some distance from some other point. On the x86, a direct address can be thought of as a displacement from address zero. On the 80x86 processors, this displacement is an offset from the beginning of a segment (the data segment in this example. So, you can think of the displacement-only addressing mode as a direct addressing mode. You can also access words on the 8086 processors :

9

8086 Memory Addressing Modes (IV) The Displacement Only Addressing Mode •By default, all displacement-only values provide offsets into the data segment. If you want to provide an offset into a different segment, you must use a segment override prefix before your address. •For example, to access location 1234h in the extra segment (es) you would use an instruction of the form mov ax,es:[1234h]. Likewise, to access this location in the code segment you would use the instruction mov ax, cs:[1234h]. •The ds: prefix in the previous examples is not a segment override. The U uses the data segment by default. These specific examples require ds: because of MASM's syntactical limitations.

10

•

The Reg. Indirect Addressing Modes (I) The 80x86 Us let you access memory indirectly through a

using the indirect addressing modes. There are four forms of this addressing mode on the 8086, best demonstrated by the following instructions: mov al, [bx] mov al, [bp] mov al, [si] mov al, [di] • As with the x86 [bx] addressing mode, these four addressing modes reference the byte at the offset found in the bx, bp, si, or di , respectively. The [bx], [si], and [di] modes use the ds segment by default. The [bp] addressing mode uses the stack segment (ss) by default. • You can use the segment override prefix symbols if you wish to access data in different segments. The following instructions demonstrate the use of these overrides: mov al, cs:[bx] mov al, ds:[bp] mov al, ss:[si] mov al, es:[di]

11

The Reg. Indirect Addressing Modes (II)

Intel refers to [bx] and [bp] as base addressing modes and bx and bp as base s (in fact, bp stands for base pointer). Intel refers to the [si] and [di] addressing modes as indexed addressing modes (si stands for source index, di stands for destination index). However, these addressing modes are functionally equivalent. Note: the [si] and [di] addressing modes work exactly the same way, just substitute si and di for bx above.

12

Indexed Addressing Modes (I) • The indexed addressing modes use the following syntax: mov al, disp[bx] mov al, disp[bp] mov al, disp[si] mov al, disp[di] • If bx contains 1000h, then the instruction mov cl,20h[bx] will load cl from memory location ds:1020h. Likewise, if bp contains 2020h, mov dh,1000h[bp] will load dh from location ss:3020. • The offsets generated by these addressing modes are the sum of the constant and the specified . • The addressing modes involving bx, si, and di all use the data segment, the disp[bp] addressing mode uses the stack segment by default. • As with the indirect addressing modes, you can use the segment override prefixes to specify a different segment: mov al, ss:disp[bx] mov al, es:disp[bp] mov al, cs:disp[si] mov al, ss:disp[di] 13

Indexed Addressing Modes (II)

• You may substitute si or di in the figure above to obtain the [si+disp] and [di+disp] addressing modes. • Note that Intel still refers to these addressing modes as based addressing and indexed addressing. Intel's literature does not differentiate between these modes with or without the constant.

14

Based Indexed Addressing Modes (I) • •

• •

•

The based indexed addressing modes are simply combinations of the indirect addressing modes. These addressing modes form the offset by adding together a base (bx or bp) and an index (si or di). The allowable forms for these addressing modes are mov al, [bx][si] mov al, [bx][di] mov al, [bp][si] mov al, [bp][di] Suppose that bx contains 1000h and si contains 880h. Then the instruction mov al,[bx][si] would load al from location DS:1880h. Likewise, if bp contains 1598h and di contains 1004, mov ax,[bp+di] will load the 16 bits in ax from locations SS:259C and SS:259D. The addressing modes that do not involve bp use the data segment by default. Those that have bp as an operand use the stack segment by default.

15

Based Indexed Addressing Modes (II)

You substitute di in the figure above to obtain the [bx+di] addressing mode.

You substitute di in the figure above to obtain the [bp+di] addressing mode. 16

Based Indexed Plus Displacement Addressing Mode (I) These addressing modes are a slight modification of the base/indexed addressing modes with the addition of an eight bit or sixteen bit constant. The following are some examples of these addressing modes:

mov al, disp[bx][si] mov al, disp[bx+di] [bp+si+disp] mov al, [bp][di][disp]

mov al,

You may substitute di in the figure above to produce the [bx+di+disp] addressing mode. 17

Based Indexed Plus Displacement Addressing Mode (II)

• You may substitute di in the figure above to produce the [bp+di+disp] addressing mode. • Suppose bp contains 1000h, bx contains 2000h, si contains 120h, and di contains 5. Then, mov al,10h[bx+si] loads al from address DS:2130; mov ch,125h[bp+di] loads ch from location SS:112A; and mov bx,cs:2[bx][di] loads bx from location CS:2007. 18